Wheel Apparatus has been involved with the ASTM Standardization Process for over 30 Optional Test Kits are available for either ASTM B or G testing. EPI Materials Testing group does custom wear testing and three standardized wear tests for their clients, ASTM G65, G, and B ASTM Methods ASTM G65 – 04 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus ASTM G – 02() Standard.

Author: Najind Nikobar
Country: Sierra Leone
Language: English (Spanish)
Genre: Finance
Published (Last): 12 February 2010
Pages: 150
PDF File Size: 5.74 Mb
ePub File Size: 20.95 Mb
ISBN: 191-3-11324-431-2
Downloads: 49347
Price: Free* [*Free Regsitration Required]
Uploader: Samugore

The value of the test method lies in predicting the ranking of materials in a similar relative order of merit as would occur in an abrasive environment. The consumption of sand is also high due to the large mass flow required. G1005 alternative abradant feed system is designed to give a range of constant feed rates and produce an even monolayer of particles on the wheel in front of the contact.

Please first verify your v105 before subscribing to alerts. Abradant particle shape or angularity It is clear, therefore, that a single set of test conditions will not be sufficient for determining the wear resistance of diverse materials.

Abradant properties, namely hardness and crushing strength 6. Link to Active This link will always route to the current Active version of the standard. In all cases the abrasive used is rounded quartz grain sand.

If the document is revised or amended, you will be notified by email.

The wear resistance of a material cannot be predicted reliably from simple properties such as bulk hardness, elastic modulus or tensile strength. Smaller quantities are desirable if non-standard abradants are to be used.

The particle loading is a very crucial parameter for a given abradant as this controls whether the particle cuts or is crushed in the contact. You may delete a document from your Alert Profile at any time. For wet tests, water is introduced on to the wheel surface, just behind the chute. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A number of standard methods have been developed with the aim of producing test data that will reproducibly rank materials under a specified set of conditions.

  DIGITECH STUDIO S100 PDF

The TE 65 is designed to perform tests according to the conditions described in the following methods:.

You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.

Standards Subsctiption may be the perfect solution. Download the Machine Leaflet.

ASTM G – Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests

The specimen arm may also include a strain gauge transducer to measure the dynamic friction. It is clear, therefore, that a single set of test conditions will not be sufficient for determining the wear resistance of diverse materials. The out-fall from the drum is then guided to the wheel surface down a simple chute and this produces the monolayer on the wheel surface.

It is the intent of this procedure to provide data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions. Materials of higher abrasion resistance will have a lower volume loss.

ASTM G105 – 16

Particle loading, the nominal load carried by each particle of abradant 2. However it is restricted to one type of sand and there are no facilities for adjusting the mass flow over a wide range.

The values given in parentheses are for information only. Including power supply and strain gauge amplifier. The feed rate is varied by adjusting the speed of the slotted drum. With variable speed drive motor and manually controlled pneumatic loading with precision regulator, force transducer and digital display.

  BURBANO DE ERCILLA PROBLEMAS FISICA PDF

Rubber Wheel Sand Abrasion machine tests

Background Abrasive wear of satm materials handling plant e. The values given in parentheses are for information only. In practice, abrasive materials will vary considerably in hardness, crushing strength and shape from the sand specified in the ASTM standards. These define tests under dry or slurry conditions with specified loads, wheel speeds and sand feed rate.

This standard is not included in any packages. Imbeni V Hutchings I. It would be preferable to be able to run with smaller samples or even to run multiple tests on one sample, thus reducing the cost per test. ASTM B uses a steel wheel, thus providing higher stress abrasion than the rubber wheel tests. The comparison will provide a general indication of the worth of the unknown materials if abrasion is the predominant factor causing deterioration of the materials. Already Subscribed to this document.

Materials of higher abrasion resistance will have a lower volume loss. The TE 65 is designed to perform tests according to the conditions described in the following methods: We have no amendments or corrections for this standard.

Particle loading may be controlled over a wide range by adjusting the mass flow and the normal load on the test block. Load is applied by pneumatic bellows with a force transducer for load measurement.

Particle speed or cutting speed 4. Precision abradant feed system and peristaltic pump for alternative horizontal qstm configuration.