FIDC tracking water injection system osa User manual v4w Page 2 GETTING TO KNOW THE AQUAMIST HFS-6 osa Aquamist has been. WORKS has been using Aquamist Water Injection since We have seem them all since then and still strongly believe these are the most well thought out. Retired System Information. Below you will find technical info and original sales info for the systems. Aquamist HFS-6 Injection System. Aquamist HFS

Author: Malrajas Voodooran
Country: Latvia
Language: English (Spanish)
Genre: Politics
Published (Last): 18 August 2010
Pages: 106
PDF File Size: 18.24 Mb
ePub File Size: 20.40 Mb
ISBN: 479-3-53428-799-7
Downloads: 99403
Price: Free* [*Free Regsitration Required]
Uploader: Tojami

See full item description. The ERL electro-magnetic pump In order to find a pump that will reliably perform under the harsh environment of the engine bay, we have no alternatives but to design our own.

MF2 MF2 is the brain of the system, ultimately responsible for the vital functions of metering the water delivery rate. In hard water areas, occasionally clean the filter in a small glass of diluted household lime-remover. San Diego, California, United States. Back to home page Return to top.

Retired System Information

This amount is subject to change until you make payment. An additional pair of wires supplies a stablised output voltage of 5 volts for driving a MAP manifold absolute pressure sensor. Water travelling through these grooves picks up a swirling motion before leaving the small hole on the tip, causing an atomising effect, turning the water into a fine mist: Refinements such as flow rate and block jet detection can aquamst be obtained with a minimum of signal conditioning parts, hfs6- achieve a fully integrated water injection system with diagnostic capablities.

As seen form the diagram above, the construction of the center of the pump is very similar to a bicycle pump, two valves: Of course a pressure of at least 3 bar is required.

Aquamist 2c The 2c is designed for stand-alone EMS systems. RACE PUMP INFO We have ruled out the widely available centrifugal pump as the pumping mechanism, because it is always coupled to a high rotational-speed drive-motor for efficiency reasons, hence it is prone to wear; further problem arises when the water inside the pump is frozen, the drive motor has to be detached from the vane by a slipping clutch arrangement so drive-motor windings cannot be damaged as a result of jamming, this led to unnecessary expenses and complicated mechanical links.

  ELASTIC AND INELASTIC STRESS ANALYSIS SHAMES PDF

The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our High Speed Valve HSV.

Add to watch list Add to wish list. Gfs-6 to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.

The valve is terminated with water proof sealed connectors IP Back to home page.

Aquamst 2s The 2s is a fully-mappable water-injection system, is pre-pressurizedequipped with diagnostic circuitry, able to detect blocked water-jet and abnormal operation problems. A pre-pressurized system enables instant response on demand.

For those who want a 3-D water injection MAP but do not want to spend the time-consuming task of mapping, this system is perfect for you. A high pressure pump with NO mechanical links, thus eliminated damages caused by jamming.

In hard water areas, clean the filter in a small glass of diluted household lime-remover occasionally.

Retired System Information | Howerton Engineering

Electrical and Mechanical specifications Condition Input Voltage: Flow and pressure characteristics are controlled by varying the frequency and the duration of the electrical pulse fed to the solenoid.

The MF2 uses incoming RPM and pressure signals from the sensors in the engine bay and compares them with a pre-programmed map set by the user. The color supplied with the kit is semi-translucent white, but red, yellow, green, blue and black are available hfs6- request.

The aquamiist is activated when an adjustable qquamist switch, fitted to the inlet manifold, reaches its preset point: Thread size of the jet is M8x0. Water is being filled and retained between the two valves during the induction stroke armature is pulled against the springwater is then pushed out by the action of compressed spring and the armature when the electric-field is shut-off, high pressure is the product of spring force and hcs-6 cross-section area of the armature tip.

In addition, high speed drive motor tends to suffer from burn-out under prolonged continuous running. After several signal conditioning stages it finally arrives at the pulse-width-modulator stage, and the output signal is then aqyamist into digital pulses before being sent to the electro-magnetic water valve. Estimated on or before Mon. The green LED indicates successful detection of fuel injection pulses and the red LED lights up when water is being injected preset manifold pressure is reached.

  JIAOGULAN WIRKUNG PDF

The new design is also one of the easiest to install as well. There are no mechanical links between the piston and the drive motor: The system provides a pre-pressurized water line up to 8 bars and the hfs–6 rate is metered by our latest High speed Valve HSV.

Peak pressure can go as high as psi! For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab. For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.

Delivery time is estimated using our proprietary method which is based on the buyer’s proximity to the item location, the shipping service selected, the seller’s shipping history, and other factors.

Water travels through these grooves, acquiring a swirling motion before leaving the small hole on the tip: Aquamist 1s The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, plus all the aqaumist hardware to form the basis of a starter kit. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.

As the pulsed signal from the pressure switch is directly proportional to the flow of water, it can either be recorded by an on-board data acquistion system for diagnostic purposes or read by the control ECU to monitor blockage or water jet and other faults that may arise.

aquajist Sep 20, Skip to main content. Sell one like this. In addition, it has diagnostic circuitry designed to detect blocked water-jets and cut pipes. As usual, except for the water tank, the system is supplied with everything needed to be fitted with ease. With the best failsafe system in the industry, and a standard 13ohm injector that could be be driven by a spare PWM channel from your EMS, the HFS-5 easily integrates into nearly any application.